In this article below you might get additional wonderful advice related to How to Install a Bathtub Yourself.
Setting up a bath tub isn't specifically rocket science, however it does need strong plumbing, carpentry, as well as occasionally, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably difficult job. If the old bathtub is readily easily accessible, the job can relocate speedily; if you have to open up a wall surface to remove the old bathtub and position the brand-new bath tub, the task is much harder. In either case, the project is within a house handyman's abilities, although you will need an assistant to move out the old bathtub and also set in the brand-new one. See to it you have certified on your own for the job and also fit attempting it. Instead of working with a contractor to take over a halfway-completed task, it is far better to think about using one before you start. Opportunities are you might require a professional plumber to make tube connections.
This article will certainly assist you mount a brand-new bathtub in your bathroom if you have already purchased a new tub as well as do not require to transform the setup of your previous water supply pipelines.
Your devices and product list ought to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is separate the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of getting rid of the existing taps can be fairly troublesome due to the limited gain access to that is often the instance.
Use a container wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipelines to the taps. Have a towel ready for the continuing to be water that will originate from the pipes. As soon as the supply pipes have actually been eliminated, make use of the same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to quit the solitary taps from transforming throughout this process. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any old sealing substance.
Before carrying on to fit the brand-new taps, compare the pipeline links on the old faucets to the new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic adapter to prevent damage to the thread. One end of the port fits on the plastic tail of the tap as well as the various other end gives a link to the existent supply pipes.
If you need to fit a monobloc, after that you will certainly call for minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next off, place the faucet in the placing opening in the bath/basin making sure that the washers are in place between the faucet and also the sink. Safeguard the faucet in place with the maker offered backnut. Once the faucet is safely in place, the supply pipes can be connected to the tails of the faucets. The taps can either be connected by using corrugated copper piping or with normal tap adapters. The former type ought to be linked to the tap ends first, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Mounting the Bath tub
Using the two wood boards under its feet, position the bathtub in the required placement. The wood boards are practical in uniformly spreading the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four small factors.
The following goal is to make certain that the bath tub is leveled all round. This can be accomplished by checking the spirit level as well as changing the feet on the bathtub till the level checks out degree.
To mount taps, fit the bottom of the outermost versatile tap adapter to the suitable supply pipeline by making a compression sign up with; then do the same for the other tap.
Activate the water as well as check all joints and also brand-new pipework for leaks and tighten them if essential. Fill up the bathtub as well as also examine the overflow electrical outlet and the regular electrical outlet for leaks.
Finally, deal with the bath paneling as described in the maker's instruction manual. Tiling and securing around the bathtub needs to wait up until the bathtub has actually been used at the very least when as this will certainly settle it into its last setting.
Preparing for the Installation
To start with, the supporting framework supplied with the bathroom ought to be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the tap features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a supporting plate under the faucets system to stop stress on the bathtub.
Fit the versatile tap connectors to the bottom of both taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the electrical outlet with the hole in the bathroom. Use the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make sure you utilize every one of the supplied washing machines.
Attach the catch to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last placement.
Tiling Around the Bath tub
In the location where the bath satisfies the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is very important as the installation can move sufficient to fracture a rigid seal, causing the water to permeate the wall surface in between the bath as well as the tiling, causing difficulties with wetness and possible leakages to the ceiling listed below.
You can choose from a variety of coloured sealants to assimilate your components and fittings. They are offered in tubes and cartridges, as well as can securing voids up to a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to securing, to allow for the movement experienced when the bathtub remains in usage. The sealant can break rather early if you do not think about this motion prior to securing.
Alternatively, ceramic coving or quadrant ceramic tiles can be made use of to border the bath or shower tray. Plastic strips of coving, which are easy to use and cut to size, are likewise quickly readily available on the marketplace. It is advisable to fit the ceramic tiles utilizing waterproof or water-proof glue and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you really like reading up on Installing A Bathtub? Put a remark below. We will be glad to listen to your thoughts about this blog entry. In hopes to see you back again later on. Loved our write up? Please share it. Help another person find it. I treasure reading our article about Installing A Bathtub.
Call Us Now